Forum Replies Created
-
Posts
-
I am running steam portal 1 on windows 7. I could not get it to boot straight to dk2. With display set to dk2 extended desktop, tell vorpx to use windows setting for monitor selection. Put portal desktop icon in toward the middle of screen off to one side. With vorpx turned on, go to your windows display settings and switch the dk2 to primary monitor. Now on dk2 desktop click portal icon to start. This works for me, but it is hard to see to switch back to your main monitor when you are done playing. Stretching the start menu taller can make it visible in the rift when set to primary, helps to see to click display setting tab when done with game.
Make sure to load game first on main monitor and switch resolution to 1920X1080, fullscreen. If this is not already set before attempting to start game you will have many more issues. I would also recommend in game graphics settings maxing the fov setting, turning on motion blur (seems to help with motion sickness for me). Lastly turn on gamepad control ingame and disable vorpx gamepad control. Ingame controller setup is not conflicting with head tracking for me.
Hope this helps.I just finished Bioshock Infinite with dk2 and vorpx which was one of the greatest game experiences of my life. This was the steam version, running windows 7 on an evga nvidea 640 with 8 gb ddr2, with graphics set to very high. I used the following setup:
In game settings:
Start Bioshock Infinite without vorpx first.
Go to options, graphics, set field of view to max.
Ensure game is fullscreen, and 1920X1080.
Start New Game, enter the light house, exit game.
(Ensuring ini creation, and a good point to trigger autosave to jump in and out of game while adjusting)
Startup Vorpx.
Right click tray icon, Configure Vorpx, General Settings,
Under Disaply/Monitors set to Show on Rift DK2 and disable Aero on game start.
(I have had alot of luck with this working correctly since the patch)
Apply and close.
Restart Bioshock Infinite with vorpx on.
You should be able to see well enough to continue your game.
(Use middle mouse click edge peak if needed to enter game)
Ingame vorpx settings:
Once ingame push Delete on your keyboard to bring up vorpx menu.
Click Mouse wheel to zoom back in to see menu clearly.
On Main tab:
Set 3d Reconstruction Z Normal
Seperation (3d-strength) 2.00
Depth Weighting (Near-Far) 1.00
(These are the most immersive 3d setting I found, that do not distort quality or cause my stomach to turn)
On Display Tab:
Fix Chromatic Aberration On
Image Zoom 0.67
(This will pull the camera back far enough to capture most of the screen without taking you out of the screen)
On Input Tab:
HT Sensitivity .38
HT Roll On
HT Smoothing Very Low
(This will seem a bit slow, once you reach the target practice area i suggest you practice till perfect learning to aim and shoot using head tracking before you proceed, and tweak these settings to what suits you. Alot of people dislike this method of shooting and want the crosshair disconnected, but having tried steamvr halflife 2 I can tell you hands down, I love aiming with headtracking. You will also want to tweak your right joystick sensitivity ingame control options to your liking, I also found that a lower sensitivity worked for me.)
Handle Gamepads Internally Off
Head Tracking as Gamepad Off
(This will allow you to play with an xbox controller using in game setup, which does not coflict with head tracking for me)
OK&Save (exit vorpx panel)
Exit Game one more time.
INI Settings:
Open the following folder:
C:\Users\(your username)\Documents\My Games\BioShock Infinite\XGame\Config
Open XUserOptions.ini with notepad.
Change:
MaxUserFOVOffsetPercent=00.000000
To:
MaxUserFOVOffsetPercent=28.570000
(This will boost your fov back far enough to make the depth feel correct)
Save and Close
Open XGame.ini with notepad.
Change:
[XCore.XScreenManager]
bUseDefaultSafeRect=true
SafeRectX0=0
SafeRectY0=0
SafeRectX1=1920
SafeRectY1=1080
MaxDefaultSafeRectAspectRatio=1
To:
[XCore.XScreenManager]
bUseDefaultSafeRect=false
SafeRectX0=0
SafeRectY0=0
SafeRectX1=900
SafeRectY1=700
MaxDefaultSafeRectAspectRatio=0
Save and Close
(This last edit alters the positioning of your hud elements. These settings will pull your healthbar, vigorbar etc inside your field of view. This will allow you to enjoy the game without ever having to use edge peak)
Restart Bishock infinite and enjoy.